CW25A

FAQs & Troubleshooting

FAQs & Troubleshooting

How do I thread my machine? (for models equipped with a needle threader)

Upper threading

(1) Spool pin
(2) Thread guide (back)
(3) Thread guide (front)
(4) Thread take-up lever
(5) Mark on the handwheel

 

  • When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break.
  • Never use a thread weight of 20 or lower.
  • Use the needle and the thread in the correct combination. For details on the correct combination of needles and threads, refer to the section of “FABRIC, THREAD, AND NEEDLE COMBINATIONS” on the Operation Manual.
  • The needle threader can be used with a 75/11 through 100/16 home sewing machine needle. However, the needle threader cannot be used with a 65/9 home sewing machine needle. When using special thread such as transparent nylon thread or metallic thread, the needle threader cannot be used.
  • Thread with a thickness of 130/120 or thicker cannot be used with the needle threader.
  • The needle threader cannot be used with the wing needle or the twin needle.
 

 

  1. Turn off the machine.
     

    Turn off the machine.

     

  2. Raise the presser foot lever.
     

    Raise the presser foot lever.

     

    (1) Presser foot lever

     

  3. Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up.
     

    Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up.

     

    (1) Mark on the wheel

     

    If the needle is not correctly raised, the sewing machine can not be threaded.
     

     
  4. Pull up the spool pin completely.
     

    Pull up the spool pin completely.

     

  5. Put a spool of thread on this pin.
     

    Put a spool of thread on this pin.

     

    If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin and cause the needle to break.

     
  6. While holding the thread from the spool with your right hand, pass the thread toward you, in the groove on the thread guide.
     

    While holding the thread from the spool with your right hand, pass the thread toward you, in the groove on the thread guide.

     

    (1) Spring

    Make sure that the spring in the groove catches the thread.
     

     
  7. Feed the upper thread as shown in the following illustration.
     

    Feed the upper thread as shown in the following illustration.

     

  8. Make sure you guide the thread through the thread take-up lever from right to left as shown in the following illustration.
     

    Make sure you guide the thread through the thread take-up lever from right to left as shown in the following illustration.

     

    (1) Thread take-up lever

    If the thread take-up lever is lowered, the upper thread can not be wrapped around the thread take-up lever.
    Make sure you raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up.

     
  9. Put the thread behind the guide above the needle.
     

    Put the thread behind the guide above the needle.

     

    (1) Needle bar thread guide

    The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand.

     
  10. Lower the presser foot lever.
     

    Lower the presser foot lever.

     

    (1) Presser foot lever

     

  11. Make sure that the mark on the wheel points up as shown in the following illustration.
     

    Make sure that the mark on the wheel points up as shown in the following illustration.

     

    (1) Mark on the wheel

     

  12. While lowering the needle threader lever, hook the thread onto the guide.
     

     While lowering the needle threader lever, hook the thread onto the guide.

     

    (1) Needle holder
    (2) Needle threader lever
    (3) Guide

     

  13. Pull down the needle threader lever as much as possible, and then turn the lever toward the back of the machine (away from you).
    Make sure that the hook passes through the eye of the needle and grabs the thread.
     

    Pull down the needle threader lever as much as possible, and then turn the lever toward the back of the machine (away from you).

     

    (1) Hook
    (2) Thread

    Hold the thread in front of the needle to make sure that the hook grabs it.
     

     
  14. While lightly holding the thread, turn the needle threader lever toward the front of the machine (toward you). The hook will pull the thread through the needle.
     

    While lightly holding the thread, turn the needle threader lever toward the front of the machine (toward you).

     

  15. Raise the needle threader lever.
     

    Raise the needle threader lever.

     

  16. Pull the loop of the thread passed through the eye of the needle toward the rear of the machine.
     

    Pull the loop of the thread passed through the eye of the needle toward the rear of the machine.

     

    (1) Loop of thread

    • Be careful not to pull on the thread with force or it may bend the needle.
    • If the thread does not pass through the eye of the needle, start from step 11 again.
     

Drawing up the lower thread

 

  1. Raise the presser foot lever.

    Raise the presser foot lever.
    (1) Presser foot lever

     

  2. While lightly holding the end of the upper thread, slowly turn the handwheel toward you (counterclockwise) by hand to lower and then raise the needle.
     

    While lightly holding the end of the upper thread, slowly turn the handwheel toward you (counterclockwise) by hand to lower and then raise the needle.

     

  3. Pull on the upper thread to draw up the lower thread.
     

    Pull on the upper thread to draw up the lower thread.

     

    (1) Upper thread
    (2) Lower thread

     

  4. Pull out about 5 cm (2 inches) of both threads and put them toward the back of the machine under the presser foot.
     

    Pull out about 5 cm (2 inches) of both threads and put them toward the back of the machine under the presser foot.

     

    (1) Upper thread
    (2) Lower thread

     

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

CW25A, T3125

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.