Home > Troubleshooting > Error and Maintenance Messages
Error and Maintenance Messages
As with any sophisticated office product, errors may occur and supply items may have to be replaced. If this happens, your machine identifies the error or required routine maintenance and shows the appropriate message. The most common error and maintenance messages are shown in the table.
Follow the instructions in the Action column to solve the error and remove the message.
You can correct most errors and perform routine maintenance by yourself. If you need more tips: Visit support.brother.com/faqs.
Error Message | Cause | Action |
---|
2-sided Disabled | The back cover of the machine is not closed completely. | Close the back cover of the machine until it locks in the closed position. |
The 2-sided tray is not installed completely. | Install the 2-sided tray firmly in the machine. |
Access Denied | The function you want to use is restricted by Secure Function Lock 3.0. | Ask your administrator to check your Secure Function Lock Settings. |
Calibration | Calibration failed. |
|
Cannot Detect | Your machine cannot detect the toner cartridge. | Remove the toner cartridge and drum unit assembly for the color that is indicated on the LCD. Take out the toner cartridge, and put it back into the drum unit again. Re-install the toner cartridge and drum unit assembly back in the machine. See Related Information: Replace the Toner Cartridge. |
Cannot Print ## | The machine has a mechanical problem. |
|
Cartridge Error | The toner cartridge is not installed correctly. | Remove the toner cartridge and drum unit assembly for the color that is indicated on the LCD. Take out the toner cartridge, and put it back into the drum unit again. Install the toner cartridge and drum unit assembly back in the machine. If the problem continues, contact Brother Customer Service or your local Brother dealer. |
Condensation | Condensation may have formed inside the machine after a room temperature change. | Leave the machine turned on. Wait for 30 minutes with the top cover in the open position. Then turn off the machine and close the cover. Turn it on again. |
Cooling Down | The temperature inside the machine is too high. The machine pauses its current print job and goes into cooling down mode. | Wait until the machine has finished cooling down. Make sure all vents on the machine are clear of obstructions. When the machine has cooled down, it will resume printing. |
Cover is Open | The top cover is not completely closed. | Open and then firmly close the top cover of the machine. |
The fuser cover is not completely closed. | Close the fuser cover located under the back cover of the machine. |
Drum ! | The corona wire on the drum unit must be cleaned. | Clean the corona wire on the drum unit. ![]() See Related Information: Clean the Corona Wires. If the problem continues, replace the drum unit with a new one. |
Drum Stop | It is time to replace the drum unit. | Replace the drum unit. See Related Information: Replace the Drum Unit. |
Jam 2-sided | The paper is jammed in the 2-sided tray or inside the back cover. | Remove the 2-sided tray and open the back cover to pull out all jammed paper. |
Jam Inside | The paper is jammed inside the machine. | Open the top cover, remove the toner cartridge and drum unit assemblies, and gently remove the jammed paper. Reinstall the toner cartridge and drum unit assemblies into the machine. Close the top cover. |
Jam MP Tray | The paper is jammed in the MP tray. | Remove all jammed paper from in and around the MP tray. Press Retry. |
Jam Rear | The paper is jammed in the back of the machine. | Open the fuser cover and gently remove the jammed paper. Close the fuser cover. If the error message remains, press Retry. |
Jam Tray1 Jam Tray2 | The paper is jammed in the indicated paper tray. | Pull out the paper tray and gently remove all jammed paper as shown in the animation on the LCD. |
Limit Exceeded | The print limit set in Secure Function Lock 3.0 was reached. | Ask your administrator to check your Secure Function Lock Settings. |
Media Type Mismatch | The media type specified in the printer driver differs from the paper type specified in the machine's menu. | Load the correct type of paper in the tray indicated on the LCD, and then select the correct media type in the Paper Type setting on the machine. |
No Belt Unit | The belt unit is not installed or not installed correctly. | Reinstall the belt unit. |
No Drum Unit | The drum unit is not installed correctly. | Reinstall the toner cartridge and drum unit assembly. |
No HUB Support | A USB hub device is connected to the USB host connector. | Disconnect the USB hub device from the USB host connector. |
No Paper MP Tray | The MP tray is out of paper, or paper is not loaded correctly in the MP tray. | Do one of the following:
|
No Paper Tray1 No Paper Tray2 | The machine failed to feed paper from the indicated paper tray. | Do one of the following:
|
No Toner | The toner cartridge is not installed or not installed correctly. | Remove the toner cartridge and drum unit assembly. Remove the toner cartridge from the drum unit, and reinstall the toner cartridge back into the drum unit. Reinstall the toner cartridge and drum unit assembly back in the machine. If the problem continues, replace the toner cartridge. |
No Tray1 No Tray2 | The paper tray is not installed or not installed correctly. | Reinstall the paper tray indicated on the LCD. |
No Waste Toner | The waste toner box is not installed or not installed correctly. | Reinstall the waste toner box. |
Out of Memory | The machine’s memory is full. | Press |
Print Data Full | The machine’s memory is full. | Press |
Registration | Registration failed. |
|
Replace Toner | The toner cartridge is at the end of its life. The machine stops all print operations. | Replace the toner cartridge for the color indicated on the LCD. See Related Information: Replace the Toner Cartridge. |
Replace WT Box | It is time to replace the waste toner box. | Replace the waste toner box with a new one. See Related Information: Replace the Waste Toner Box. |
Screen Init. Fail | The touchscreen was pressed before the power on initialization was completed. | Make sure nothing is touching the touchscreen. |
Debris may be stuck between the lower part of the touchscreen and its frame. | Insert a piece of stiff paper between the lower part of the touchscreen and its frame and slide it back and forth to push out any debris. |
Self-Diagnostic | The temperature of the fuser unit does not rise to a specified temperature within the specified time. | Press and hold |
The fuser unit is too hot. |
Size Error 2-sided | The paper size specified in the machine's paper size setting is not available for automatic 2-sided printing. | Press Load the correct size of paper in the tray and set the tray for that paper size. Choose a paper size supported by 2-sided printing. Paper sizes available for automatic 2-sided printing are Letter, Legal, Mexico Legal, India Legal and Folio. |
The paper in the tray is not the correct size and is not available for automatic 2-sided printing. |
Size Error | The paper size defined in the printer driver is not supported by the defined tray. | Choose a paper size supported by the defined tray. |
Size Mismatch | The paper in the tray is not the correct size. | Load the correct size of paper in the tray and set the size of paper for the tray. Press Retry. |
Supplies Belt End Soon | The belt unit is near the end of its life. | Order a new belt unit before the LCD displays Replace Belt. |
Supplies Drum End Soon | The drum unit is near the end of its life. | Order a new drum unit before the LCD displays Replace Drum. |
Supplies Replace Belt | It is time to replace the belt unit. | Replace the belt unit with a new one. See Related Information: Replace the Belt Unit. |
Supplies Replace Drum | It is time to replace the drum unit. | Replace the drum unit for the color indicated on the LCD. See Related Information: Replace the Drum Unit. |
If this message is displayed even after replacing the drum unit with new one, the drum unit counter was not reset. | Reset the drum unit counter. See Related Information: Replace the Drum Unit. |
Supplies Toner Low: X (X indicates the toner cartridge or drum unit color that is near the end of its life. BK=Black, C=Cyan, M=Magenta, Y=Yellow.) | If the LCD displays this message, you can still print. The toner cartridge is near the end of its life. | Order a new toner cartridge before the LCD displays Replace Toner. |
Supplies WT Box End Soon | The waste toner box is almost full. | Order a new waste toner box before the LCD displays Replace WT Box. |
Toner Error | One or more toner cartridges are not installed or not installed correctly. | Pull out the drum units. Remove all the toner cartridges, and then put them back into the drum units. |
Too Many Trays | The number of installed Optional Trays exceeds the maximum number. | Reduce the number of Optional Trays. |
Unusable Device | An unsupported USB device has been connected to the USB host connector. | Unplug the device from the USB host connector. |
Unusable Device Remove the Device. Turn the power off and back on again. | A defective USB device or a high power consumption USB device has been connected to the USB direct interface. |
|