FAQs & Troubleshooting
![]() |
Popular |
68 Results
- 1How to use the Multi-purpose Screwdriver. [ Position “2” ]
- 2How to use the Multi-purpose Screwdriver.
- 3How to use the Multi-purpose Screwdriver. [ Position “3” ]
- 4How to use the Multi-purpose Screwdriver. [ Position “1” ]
- 5"This USB media cannot be used." message appears on the LCD. What does it mean?
- 6Where do I put the oil in my machine?
- 7How do I clean the race?
- 8When I sew an embroidery pattern design exported as DST format in PE-DESIGN, how do I specify whether or not the jump stitches are cut on the embroidery machine of the Innov-is series?
- 9How do I thread my machine ?
- 10"Preventive maintenance is recommended" appears on the LCD.
- 11When tansferring an embroidery data from PE-DESIGN 11 to the embroidery machine connected to the computer with a USB cable, the message "Disk full while accessing [filename]." appears.
- 12How do I attach or remove the Embroidery Unit?
- 13How do I adjust an alternate bobbin case(with pink marking or no marking) using an embroidery pattern?
- 14"Sensor module error." message appears on the LCD. What does it mean?
- 15"The upper thread may not be threaded correctly. Thread the upper thread from the beginning." message appears on the LCD. What does it mean?
- 16Why is the outline sewing off the pattern?
- 17"The safety device has been activated. Is the thread tangled? Is the needle bent?" message appears on the LCD. What does it mean?
- 18"Attach the embroidery frame." message appears on the LCD. What does it mean?
- 19How do I change the needle ?
- 20"Data volume is too large for this pattern." message appears on the LCD. What does it mean?
- 21Embroidery
- 22If the thread breaks during sewing.
- 23"Set the clock." message appears on the LCD. What does it mean?
- 24"OK to revert to the original position and/or angle?" message appears on the LCD. What does it mean?
- 25"OK to delete the selected pattern?" message appears on the LCD. What does it mean?
- 26How do I set the bobbin ?
- 27"This key does not operate when the needle is down. Raise the needle and press the key again." message appears on the LCD. What does it mean?
- 28"This file exceeds the data capacity and cannot be used. Use a suitable size file." message appears on the LCD. What does it mean?
- 29How do I calibrate the sensor pen?
- 30When I create an embroidery pattern design on PE-DESIGN(PE-DESIGN, PE-DESIGN Lite, or PED-Basic), what Design Page Size is my sewing machine?
- 31"There is no needle plate cover. Attach a needle plate cover." message appears on the LCD. What does it mean?
- 32"The pattern field extends out of the pattern area, repeat setting the position and angle using the sensor pen." message appears on the LCD. What does it mean?
- 33"The needle will move. Keep your hands etc. away from the needle area." message appears on the LCD. What does it mean?
- 34"USB media error" message appears on the LCD. What does it mean?
- 35"This file cannot be used." message appears on the LCD. What does it mean?
- 36"OK to reset the pattern’s border setting, position and/or angle?" message appears on the LCD. What does it mean?
- 37How do I attach or remove the embroidery frame ?
- 38How do I wind the bobbin?
- 39"OK to automatically lower the presser foot?" message appears on the LCD. What does it mean?
- 40"This USB media is incompatible." message appears on the LCD. What does it mean?
- 41"Not enough available memory to save the pattern. Delete another pattern?" message appears on the LCD. What does it mean?
- 42"The bobbin thread is almost empty." message appears on the LCD. What does it mean?
- 43"Use the presser foot lifter button to lower the presser foot." message appears on the LCD. What does it mean?
- 44How do I create a space between characters?
- 45"Turn off the power and replace the needle plate." message appears on the LCD. What does it mean?
- 46Why does the lower thread keep breaking?
- 47Upper threading (Point)
- 48How do I specify the embroidering location with the sensor pen? (Specifying the embroidery pattern location by selecting the pattern center with the sensor pen.)
- 49How do I adjust the clock on the display?
- 50"Lower the presser foot lever." message appears on the LCD. What does it mean?