Search

Site Map

Home > Network > Wireless Network Settings > Use the Wireless Network > Configure Your Machine for a Wireless Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS)

Configure Your Machine for a Wireless Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS)

Related Models:ADS‑1350W / ADS‑1800W

If your wireless access point/router supports WPS, you can use the Personal Identification Number (PIN) Method to configure your wireless network settings.

The PIN Method is one of the connection methods developed by the Wi-Fi Alliance®. By submitting a PIN created by an Enrollee (your machine) to the Registrar (a device that manages the wireless LAN), you can set up the wireless network and security settings. For more information on how to access WPS mode, see the instructions provided with your wireless access point/router.

Type A
Connection when the wireless access point/router (1) doubles as the Registrar.
image
Type B
Connection when another device (2), such as a computer, is used as the Registrar.
image

ADS-1350W

Before configuring your wireless network settings, write down the eight-digit PIN located on the bottom of the machine and marked "PIN(WPS)".

  1. Press and hold image for two seconds.
  2. When the Wi-Fi LED starts flashing, press image. Your machine starts searching for a wireless access point/router.
  3. Using a computer connected to the network, in your browser's address bar, type the IP address of the device you are using as the Registrar. (For example: http://192.168.1.2)
  4. Go to the WPS settings page and type the PIN, and then follow the on-screen instructions.
    image
    • The Registrar is usually the wireless access point/router.
    • The settings page may differ depending on the brand of wireless access point/router. For more detailed information, see the instructions supplied with your wireless access point/router.
If using a Windows 10 or Windows 11 computer as a Registrar, complete the following steps:
  1. Hold down the image key and press the image key on the computer's keyboard to launch Run.
  2. Type "control printers" in the Open: field and click OK.
    image
    The Devices and Printers window appears.
    image
    If the Devices and Printers window does not appear, click View more devices>More devices and printer settings.
  3. Click Add a device.
    image
    • To use a Windows 10 or Windows 11 computer as a Registrar, you must register it to your network in advance. For more information, see the instructions supplied with your wireless LAN access point/router.
    • If using Windows 10 or Windows 11 as a Registrar, you can install the scanner driver after wireless configuration is finished by following the on-screen instructions. To install the driver and software necessary to use your machine, go to your model's Downloads page at support.brother.com/downloads.
  4. Select your machine and click Next.
  5. Type the PIN, and then click Next.
  6. Click Close.
If your wireless device is connected successfully, the Wi-Fi LED stops flashing and remains lit.
You have completed the wireless network setup. To install drivers and software necessary for operating your machine, go to your model's Downloads page at support.brother.com/downloads.

ADS-1800W

  1. Press image [Settings]>[Network]>[WLAN(Wi-Fi)]>[WPS/PIN Code].
  2. When [Enable WLAN? Do you want to continue?] appears, press [Yes].
    The wireless setup wizard starts. To cancel, press [No].
  3. The LCD displays an eight-digit PIN and the machine starts searching for a wireless access point/router.
  4. Using a computer connected to the network, in your browser's address bar, type the IP address of the device you are using as the Registrar. (For example: http://192.168.1.2)
  5. Go to the WPS settings page and type the PIN, and then follow the on-screen instructions.
    image
    • The Registrar is usually the wireless access point/router.
    • The settings page may differ depending on the brand of wireless access point/router. For more detailed information, see the instructions supplied with your wireless access point/router.
If using a Windows 10 or Windows 11 computer as a Registrar, complete the following steps:
  1. Hold down the image key and press the image key on the computer's keyboard to launch Run.
  2. Type "control printers" in the Open: field and click OK.
    image
    The Devices and Printers window appears.
    image
    If the Devices and Printers window does not appear, click View more devices>More devices and printer settings.
  3. Click Add a device.
    image
    • To use a Windows 10 or Windows 11 computer as a Registrar, you must register it to your network in advance. For more information, see the instructions supplied with your wireless LAN access point/router.
    • If using Windows 10 or Windows 11 as a Registrar, you can install the scanner driver after wireless configuration is finished by following the on-screen instructions. To install the driver and software necessary to use your machine, go to your model's Downloads page at support.brother.com/downloads.
  4. Select your machine and click Next.
  5. Type the PIN displayed on the machine's LCD, and then click Next.
  6. Click Close.
If your wireless device is connected successfully, the LCD displays [Connected].
You have completed the wireless network setup. To install drivers and software necessary for operating your machine, go to your model's Downloads page at support.brother.com/downloads.
Related Information
Did you find the information you needed?

find moreaccept