Search

Site Map

Home > Network > Wireless Network Settings > Use the Wireless Network > Configure Your Machine for a Wireless Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS)

Configure Your Machine for a Wireless Network Using the PIN Method of Wi-Fi Protected Setup™ (WPS)

If your wireless LAN access point/router supports WPS, you can use the Personal Identification Number (PIN) Method to configure your wireless network settings.

The PIN Method is one of the connection methods developed by the Wi-Fi Alliance®. By submitting a PIN created by an Enrollee (your machine) to the Registrar (a device that manages the wireless LAN), you can set up the wireless network and security settings. For more information on how to access WPS mode, see the instructions provided with your wireless access point/router.

Type A
Connection when the wireless LAN access point/router (1) doubles as the Registrar.
image
Type B
Connection when another device (2), such as a computer, is used as the Registrar.
image

DCP-J1050DW/MFC-J1010DW

  1. Press Settings.
  2. Press image or image to make your selections:
    1. Select [Network]. Press OK.
    2. Select [WLAN(Wi-Fi)]. Press OK.
    3. Select [WPS/PIN Code]. Press OK.
  3. When [Enable WLAN?] appears, press image.
    The wireless setup wizard starts. To cancel, press image.
  4. The LCD displays an eight-digit PIN and the machine starts searching for a wireless LAN access point/router.
  5. Using a computer connected to the network, in your browser's address bar, type the IP address of the device you are using as the Registrar. (For example: http://192.168.1.2)
  6. Go to the WPS settings page and type the PIN, and then follow the on-screen instructions.
    image
    • The Registrar is usually the wireless LAN access point/router.
    • The settings page may differ depending on the brand of wireless LAN access point/router. For more information, see the instructions supplied with your wireless LAN access point/router.
If you are using a Windows 7, Windows 8.1, or Windows 10 computer as a Registrar, complete the following steps:
  1. Do one of the following:
    • Windows 10

      Click image>Windows System>Control Panel. In the Hardware and Sound group, click Add a device.

    • Windows 8.1

      Move your mouse to the lower right corner of your desktop. When the menu bar appears, click Settings>Control Panel>Hardware and Sound>Devices and Printers>Add a device.

    • Windows 7

      Click image (Start)>Devices and Printers>Add a device.

    image
    • To use a Windows 7, Windows 8.1, or Windows 10 computer as a Registrar, you must register it to your network in advance. For more information, see the instructions supplied with your wireless LAN access point/router.
    • If you use Windows 7, Windows 8.1, or Windows 10 as a Registrar, you can install the printer driver after the wireless configuration by following the on-screen instructions. To install the driver and software necessary to use your machine, go to your model's Downloads page at support.brother.com.
  2. Select your machine and click Next.
  3. Type the PIN displayed on the machine's LCD, and then click Next.
  4. (Windows 7) Select your network, and then click Next.
  5. Click Close.

DCP-J1140DW

  1. Press image [Settings]>[Network]>[WLAN(Wi-Fi)]>[WPS/PIN Code].
  2. When [Enable WLAN?] appears, press [Yes].
    The wireless setup wizard starts. To cancel, press [No].
  3. The LCD displays an eight-digit PIN and the machine starts searching for a wireless LAN access point/router.
  4. Using a computer connected to the network, in your browser's address bar, type the IP address of the device you are using as the Registrar. (For example: http://192.168.1.2)
  5. Go to the WPS settings page and type the PIN, and then follow the on-screen instructions.
    image
    • The Registrar is usually the wireless LAN access point/router.
    • The settings page may differ depending on the brand of wireless LAN access point/router. For more information, see the instructions supplied with your wireless LAN access point/router.
If you are using a Windows 7, Windows 8.1, or Windows 10 computer as a Registrar, complete the following steps:
  1. Do one of the following:
    • Windows 10

      Click image>Windows System>Control Panel. In the Hardware and Sound group, click Add a device.

    • Windows 8.1

      Move your mouse to the lower right corner of your desktop. When the menu bar appears, click Settings>Control Panel>Hardware and Sound>Devices and Printers>Add a device.

    • Windows 7

      Click image (Start)>Devices and Printers>Add a device.

    image
    • To use a Windows 7, Windows 8.1, or Windows 10 computer as a Registrar, you must register it to your network in advance. For more information, see the instructions supplied with your wireless LAN access point/router.
    • If you use Windows 7, Windows 8.1, or Windows 10 as a Registrar, you can install the printer driver after the wireless configuration by following the on-screen instructions. To install the driver and software necessary to use your machine, go to your model's Downloads page at support.brother.com.
  2. Select your machine and click Next.
  3. Type the PIN displayed on the machine's LCD, and then click Next.
  4. (Windows 7) Select your network, and then click Next.
  5. Click Close.
Related Information
Did you find the information you needed?

find moreaccept