Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables > Settings Tables (DCP-L3550CDW)
Settings Tables (DCP-L3550CDW)
[Settings]
Level 1 | Level 2 | Level 3 | Descriptions |
---|---|---|---|
| Date & Time | - | Access the Date and Time setting menus. |
Toner | Toner Life | - | View the approximate remaining toner life. |
Test Print | - | Print a test page. | |
Calibration | Calibrate | Initiate colour calibration to check and correct colours. | |
Reset | Reset the calibration parameters to the default settings. | ||
Registration | - | Align the print position of each colour. | |
Network | Wired LAN | - | Access the Wired LAN setting menus. |
WLAN | - | Access the WLAN setting menus. | |
Screen Settings | - | - | Access the default screen setting menus. |
Eco Mode | - | - | Turn the following machine settings on at the same time.
|
Tray Setting | - | - | Access the tray setting menus. |
All Settings | - | - | Configure the detailed settings. |
Level 3 | Level 4 | Descriptions |
---|---|---|
Tray Setting | Paper Type | Select the paper type that matches the paper in the standard paper tray. |
Paper Size | Select the size of paper you loaded in the standard paper tray. | |
Check Size | Select whether to display a message telling you to check that the size and type of the paper in the machine and the machine's Paper Size and Paper Type settings match. | |
Beep | - | Adjust the beeper volume. |
LCD Settings | Backlight | Adjust the brightness of the LCD backlight. |
Dim Timer | Set how long the LCD backlight stays on after you go back to your Main Home screen. | |
Screen Settings | Main Home Screen | Set the Main Home screen. |
Copy Screen | Set the default Copy screen. | |
Scan Screen | Set the default Scan screen. | |
Notifications | Scan Result(Skip Blank Page) | Displays the total scanned pages and skipped blank pages after scanning is completed. |
Ecology | Eco Mode | Turn the following machine settings on at the same time.
|
Toner Save | Increase the page yield of the toner cartridge. | |
Sleep Time | Set how much time will pass before the machine enters Power Saving mode. | |
Quiet Mode | Decrease printing noise. | |
Auto Power Off | Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode. | |
Setting Lock | Set Password | Restrict unauthorised users from changing the machine’s settings. |
Lock Off⇒On | ||
New Password (Available only when you enter the password for the first time.) | ||
Delete Storage | Macro ID | Delete the registered Macro data. |
Font ID | Delete the registered Font data. | |
Format | Restore the Macro and Font data of your machine to the default settings. |
Level 3 | Level 4 | Descriptions |
---|---|---|
(Select a Shortcut) | Rename | Change the shortcut name. |
Edit | Change the shortcut settings. | |
Delete | Delete the shortcut. |
Level 3 | Level 4 | Level 5 | Descriptions |
---|---|---|---|
Emulation | - | - | Select the emulation mode. |
Quality | - | - | Select the print quality. |
Print Options | Font List | HP LaserJet | Print a list of the machine’s internal fonts. |
BR-Script 3 | |||
Test Print | - | Print a test page. | |
2-sided | 2-sided Print | - | Enable or disable 2-sided printing and choose long edge or short edge. |
Single Image | - | For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time. When you use preprinted paper, you must select the 2-sided Feed option. If you select 1-sided Feed for preprinted paper, the last page will be printed on the reverse side. | |
Auto Continue | - | - | Select if you want the machine to clear paper size errors or media type errors automatically, and use paper from other trays. |
Output Colour | - | - | Set the output colour. |
HP Tray Command | - | - | Select the correct version of HP LaserJet tray emulation. |
Reset Printer | - | - | Restore the printer settings to the factory settings. |
Colour Correction | Calibration | Calibrate | Initiate colour calibration to check and correct colours. |
Reset | Reset the calibration parameters to the default settings. | ||
Registration | - | Align the print position of each colour. | |
Auto Correction | - | Set the machine to perform Colour Calibration and Registration automatically. | |
Colour Settings | Setting Mode | Select whether to apply the colour print settings of the machine or the printer driver. | |
Colour Mode | Select the colour mode. | ||
Improve Grey Colour | Turn on or off to improve the image quality of shaded areas. | ||
Enhance Black Printing | Turn on or off if a black graphic does not print correctly. | ||
Brightness | Adjust the brightness. | ||
Contrast | Adjust the contrast. | ||
Red | Adjust the red colour. | ||
Green | Adjust the green colour. | ||
Blue | Adjust the blue colour. |
Level 3 | Level 4 | Level 5 | Level 6 | Descriptions |
---|---|---|---|---|
Wired LAN | TCP/IP | BOOT Method | IP Boot Tries | Select the Boot method that best suits your needs. |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (up to 32 characters) | ||
WINS Configuration | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. | ||
Ethernet | - | - | Select the Ethernet link mode. | |
Wired Status | - | - | View the current wired status. | |
MAC Address | - | - | View the machine's MAC address. | |
Set to Default | - | - | Restore the wired network settings to the factory settings. | |
Wired Enable | - | - | Turn the Wired LAN interface on or off manually. | |
WLAN | TCP/IP | BOOT Method | IP Boot Tries | Select the Boot method that best suits your needs. |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (up to 32 characters) | ||
WINS Configuration | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. | ||
Setup Wizard | - | - | Configure the wireless network settings using the setup wizard. | |
WLAN Assistant | - | - | Configure your wireless network settings using the Brother installation disc. | |
WPS | - | - | Configure your wireless network settings using the one-button push method. | |
WPS w/ PIN Code | - | - | Configure your wireless network settings using WPS with a PIN. | |
WLAN Status | Status | - | View the current wireless network status. | |
Signal | - | View the current wireless network signal strength. | ||
SSID | - | View the current SSID. | ||
Comm. Mode | - | View the current Communication mode. | ||
MAC Address | - | - | View the machine's MAC address. | |
Set to Default | - | - | Restore the wireless network settings to the factory settings. | |
WLAN Enable | - | - | Turns the wireless interface on or off. | |
Wi-Fi Direct | Push Button | - | - | Configure your Wi-Fi Direct network settings using the one-button push method. |
PIN Code | - | - | Configure your Wi-Fi Direct network settings using WPS with a PIN code. | |
Manual | - | - | Configure your Wi-Fi Direct network settings manually. | |
Group Owner | - | - | Set your machine as the Group Owner. | |
Device Information | Device Name | - | View your machine's device name. | |
SSID | - | View the Group Owner's SSID. When the machine is not connected, the LCD displays Not Connected. | ||
IP Address | - | View your machine's current IP Address. | ||
Status Information | Status | - | View the current Wi-Fi Direct network status. | |
Signal | - | View the current Wi-Fi Direct network signal strength. When your machine acts as Group Owner, the LCD always indicates a strong signal. | ||
I/F Enable | - | - | Turn the Wi-Fi Direct connection on or off. | |
Web Connect Settings | Proxy Settings | Proxy Connection | - | Change the Web connection settings. |
Address | - | |||
Port | - | |||
User Name | - | |||
Password | - | |||
Network Reset | - | - | - | Restore all network settings back to the factory settings. |
Level 3 | Level 4 | Descriptions |
---|---|---|
User Settings | - | Print a list of your settings. |
Printer Settings | - | Print a list of your Printer settings. |
Network Configuration | - | Print a list of your Network settings. |
Print File List | - | Print a list of data saved in the machine's memory. |
Drum Dot Print | - | Print the Drum Dot Check Sheet. |
WLAN Report | - | Print the wireless LAN connection results. |
Level 3 | Level 4 | Level 5 | Descriptions |
---|---|---|---|
Serial No. | - | - | Check your machine's serial number. |
Firmware Version | Main Version | - | Check your machine's firmware version. |
Sub1 Version | - | ||
Firmware Update | - | - | Update your machine to the latest firmware. |
Firmware Auto Check | - | - | View firmware information on the Main Home screen. |
Page Counter | Total | Colour | Check the total number of pages the machine has printed. |
Black and White | |||
Copy | Colour | ||
Black and White | |||
Colour | |||
Black and White | |||
Other | Colour | ||
Black and White | |||
Parts Life *1 | Drum | Black(BK) | Display the remaining life of each drum unit. |
Cyan(C) | |||
Magenta(M) | |||
Yellow(Y) | |||
Belt | - | Display the remaining life of the belt unit. | |
Fuser | - | Display the remaining life of the fuser unit. | |
PF Kit 1 | - | Display the remaining life of the PF Kit 1. |
Level 3 | Level 4 | Descriptions |
---|---|---|
Date & Time | Date | Set the date and time on your machine. |
Time | ||
Clock Type | Select the time format (12-hour or 24-hour). | |
Auto Daylight (Available only for some countries) | Set the machine to change automatically for Daylight Saving Time. | |
Time Zone | Set your time zone. | |
Reset | Machine Reset | Restore the machine settings that you have changed. |
Network Reset | Restore all network settings back to the factory settings. | |
All Settings | Restore all the machine's settings back to the factory settings and delete the personal data in the memory. You cannot see the data on the machine. | |
Factory Reset | Restore all the machine settings back to the factory settings and delete the personal data in the machine's memory. We recommend using this menu option if you want to delete all the data from the machine. | |
Local Language (Available only for some countries) | - | Change your LCD language. |