Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables > Settings Tables (DCP-L3520CDW)
Settings Tables (DCP-L3520CDW)
[General Setup]
Level 3 | Level 4 | Level 5 | Descriptions |
---|---|---|---|
Tray Setting | Paper Type | - | Set the type of paper in the paper tray. |
Paper Size | - | Set the paper size in the paper tray. | |
Print Position | X Offset | Move the print start position (at the upper left corner of pages) horizontally from -500 (left) to +500 (right) dots in 300 dpi. | |
Y Offset | Move the print start position (at the upper left corner of pages) vertically from -500 (up) to +500 (down) dots in 300 dpi. | ||
Check Paper | - | Select whether or not to display a message indicating you must check the paper type and paper size when you pull a paper tray out of the machine. | |
Beep | - | - | Adjust the beeper volume. |
Notifications | Blank Pg Skips | - | Displays the skipped pages after scanning is completed. |
Ecology | Eco Mode | - | |
Toner Save | - | Increase the page yield of the toner cartridge. | |
Sleep Time | - | Set the number of minutes before the machine enters Sleep mode. | |
Quiet Mode | - | Decrease printing noise. | |
Auto Power Off | - | Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode. | |
LCD Contrast | - | - | Adjust the LCD contrast. |
Setting Lock | - | - | Restrict unauthorised users from changing the machine’s settings. |
Delete Storage | Macro ID | - | Delete the registered Macro data. |
Stream ID | - | Delete the registered Stream data. | |
Font ID | - | Delete the registered Font data. | |
Delete All | - | Restore your machine's Macro/Stream and Font data to the factory settings. |
[Copy]
Level 3 | Level 4 | Descriptions |
---|---|---|
Density | - | Adjust the density. |
Quality | - | Choose the Copy resolution for your type of document. |
Contrast | - | Adjust the contrast for copies. |
Colour Adjust | Red | Adjust the red colour. |
Green | Adjust the green colour. | |
Blue | Adjust the blue colour. | |
ID Copy | Density | Adjust the density. |
Quality | Choose the Copy resolution for your type of document. | |
Contrast | Adjust the contrast for copies. | |
2in1/1in1 | Make 2 in 1 ID copies. |
[Printer]
Level 3 | Level 4 | Level 5 | Descriptions |
---|---|---|---|
Emulation | - | - | Set the printer emulation mode. |
Quality | - | - | Select the print quality. |
Print Options | Font List | HP LaserJet | Print a list of the machine’s internal fonts. |
BR-Script 3 | |||
Test Print | - | Print a test page. | |
2-sided | 2-sided Print | - | Turn 2-sided printing off or on and select flip on long edge or short edge. |
Single Image | - | For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time. When you use preprinted paper, you must select the 2-sided Feed option. If you select 1-sided Feed for preprinted paper, the last page will be printed on the reverse side. | |
Auto Continue | - | - | Select this setting if you want the machine to clear paper size errors or media type errors, and use paper from other trays. |
Output Colour | - | - | Set the output colour. |
Paper Type | - | - | Set the paper type. |
Paper Size | - | - | Set the paper size. |
Copies | - | - | Set the number of printed pages. |
Orientation | - | - | Set pages to print in either portrait or landscape orientation. |
Edge Emphasis | - | - | Make the text appear sharper. |
PrintPosition | X Offset | - | Move the print start position (at the upper left corner of pages) horizontally from -500 (left) to +500 (right) dots in 300 dpi. |
Y Offset | - | Move the print start position (at the upper left corner of pages) vertically from -500 (up) to +500 (down) dots in 300 dpi. | |
Auto FF | - | - | Allow the machine to print any remaining data automatically. |
HP LaserJet | Font No. | - | Set the font number. |
Font Pitch | - | Set the font pitch. (Available only for certain fonts.) | |
Font Point | - | Set the font size. (Available only for certain fonts.) | |
Symbol Set | - | Select the symbol or character set. | |
Table Print | - | Print the code table. | |
Auto LF | - | ON: CR -> CR+LF, OFF: CR -> CR | |
Auto CR | - | ON: LF -> LF+CR, FF -> FF+CR, or VT -> VT+CR OFF: LF -> LF, FF -> FF, or VT -> VT | |
Auto WRAP | - | Select whether you want a line feed and carriage return when the carriage position reaches the right margin. | |
Auto SKIP | - | Select whether you want a line feed and carriage return when the carriage position reaches the bottom margin. | |
Left Margin | - | Set the left margin at column 0 to 70 columns at 1 cpi. | |
Right Margin | - | Set the right margin at column 10 to 80 columns at 1 cpi. | |
Top Margin | - | Set the top margin distance from the top edge of the paper. | |
Bottom Margin | - | Set the bottom margin distance from the bottom edge of the paper. | |
Lines | - | Set the number of lines on each page. | |
Tray Command | - | Select this setting if a tray mismatch appears when you use the HP drivers. | |
BR-Script 3 | Error Print | - | Choose whether the machine prints the error information when errors occur. |
CAPT | - | Use CAPT (Colour Advanced Printing Technology) for optimal print quality when printing a PS file created by a non-Brother PS driver. Colours and photos appear clearer and more accurate. Print speed will be slower. | |
Multiple Page | - | Set the page layout when printing multiple pages. | |
PDF Print Opt | - | Set the PDF Print setting to print either comments (Markup) or stamps in the PDF file, along with the text. | |
Fit to Page | - | Select if the machine scales or resizes the pages in the PDF file to fit the selected paper size. | |
ClrCorrection | Correction | - | Initiate colour calibration to check and correct colours. |
Reset | - | Reset the calibration parameters to the default settings. | |
Auto Correct | - | Set the machine to perform Colour Calibration and Registration automatically. | |
ColourSettings | Setting Mode | Select whether to apply the colour print settings of the machine or the printer driver. | |
Colour Mode | Select the colour mode. | ||
Improve Gray | Turn on or off to improve the image quality of shaded areas. | ||
Enhance Black | Turn on or off if a black graphic does not print correctly. | ||
Brightness | Adjust the brightness. | ||
Contrast | Adjust the contrast. | ||
Red | Adjust the red colour. | ||
Green | Adjust the green colour. | ||
Blue | Adjust the blue colour. | ||
Reset Printer | - | - | Restore the machine settings to the factory settings. |
[Network]
Level 3 | Level 4 | Level 5 | Level 6 | Descriptions |
---|---|---|---|---|
WLAN(Wi-Fi) | Find Network | - | - | Configure the wireless network settings using the setup wizard. |
TCP/IP | Boot Method | - | Select the Boot method that best suits your needs. | |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (Up to 32 characters) | ||
WINS Config | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. | ||
WPS/PushButton | - | - | Configure your wireless network settings using the one-button push method. | |
WPS/PIN Code | - | - | Configure your wireless network settings using WPS with a PIN. | |
WLAN Status | Status | - | View the current wireless network status. | |
Signal | - | View the current wireless network signal strength. | ||
Channel | - | View the current wireless network channel. | ||
Speed | - | View the current wireless network speed. | ||
SSID | - | View the current SSID. | ||
Comm. Mode | - | View the current Communication mode. | ||
MAC Address | - | - | View the machine's MAC address. | |
WLAN Enable | - | - | Turn the WLAN on or off manually. | |
Wi-Fi Direct | Manual | - | - | Configure your Wi-Fi Direct network settings manually. |
Group Owner | - | - | Set your machine as the Group Owner. | |
Push Button | - | - | Configure your Wi-Fi Direct network settings using the one-button push method. | |
PIN Code | - | - | Configure your Wi-Fi Direct network settings using WPS with a PIN code. | |
Device Info. | Device Name | - | View your machine's device name. | |
SSID | - | View the Group Owner's SSID. When the machine is not connected, the LCD displays Not Connected. | ||
IP Address | - | View your machine's current IP Address. | ||
Status Info. | Status | - | View the current Wi-Fi Direct network status. | |
Signal | - | View the current Wi-Fi Direct network signal strength. When your machine acts as Group Owner, the LCD always indicates a strong signal. | ||
Channel | - | View the current Wi-Fi Direct network channel. | ||
Speed | - | View the current Wi-Fi Direct network speed. | ||
I/F Enable | - | - | Turn the Wi-Fi Direct connection on or off. | |
Web Based Mgmt | - | - | - | Enable or disable Web Based Management. If you enable this function, make sure you specify the connection method to use Web Based Management. |
IPsec | - | - | - | IPsec is an optional security feature of the IP protocol that provides authentication and encryption services. We recommend contacting your network administrator before changing this setting. |
Global Detect | Allow Detect | - | - | Enable or disable Global Detect, a function that detects and notifies the user when the user unintentionally connects to a global network. |
Reject Access | - | - | Disable connections to the global network. | |
Network Reset | - | - | - | Restore all network settings back to the factory settings. |
[Print Reports]
Level 3 | Descriptions |
---|---|
User Settings | Print a list of your User settings. |
Print Settings | Print a list of your Printer settings. |
Network Config | Print a list of your Network settings. |
PrintFileList | Print a list of data saved in the machine's memory. |
Drum Dot Print | Print the Drum Dot Check Sheet. |
WLAN Report | Print the wireless LAN connection results. |
[Machine Info.]
Level 3 | Level 4 | Descriptions |
---|---|---|
Serial No. | - | Display the machine's serial number. |
Firmware Version | Main Version | Check your machine's firmware version. |
Sub3 Version | ||
Security Ver. | ||
Page Counter | Total | Check the total number of pages the machine has printed during its life. |
Copy | ||
Other | ||
Parts Life | Toner | View the approximate remaining toner life for each colour. |
Drum | Display the remaining life of each drum unit. | |
Belt | Display the remaining life of the belt unit. | |
Fuser | Display the remaining life of the fuser unit. | |
[Secure Print]
Level 2 | Descriptions |
---|---|
Secure Print | You can print data saved in the machine's memory when you enter your four-digit password. Active only when the machine has secure print data. |
[Initial Setup]
Level 3 | Level 4 | Descriptions |
---|---|---|
Date & Time | Date & Time | Access the Date and Time setting menus. |
Auto Daylight (Available only for certain countries) | Set the machine to change automatically for Daylight Saving Time. | |
Time Zone | Set your time zone. | |
Reset | Machine Reset | Restore all the machine settings that you have changed. |
Network Reset | Restore all network settings back to the factory settings. | |
All Settings | Restore all the machine's settings back to the factory settings. | |
Factory Reset | Restore all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine. | |
Local Language (available for certain models) | - | Change your LCD language. |