• Basic

  • Contact

    You can enter the device's contact information (up to 255 characters).

  • Location

    You can enter the device's location information (up to 255 characters).

• Power settings

  • Auto power on

    Specifies whether the device turns on automatically when the AC Power Cord is plugged into an AC power outlet.

  • Auto sleep

    Specifies the amount of time to pass before the device automatically goes into sleep mode.

    

    • The device will automatically enter sleep mode when the specified time elapses under the following conditions:

      • The device does not receive data.
      • A LAN cable is not connected. (For wired networks)
      • In idle mode or template selection mode.
      • When no device is connected to the USB port.
      • When not communicating using the serial port.
    • Sleep mode is cancelled when the following operations are performed:

      • Any of the device buttons are pressed.
      • The Roll Compartment Cover is opened or closed.
      • The device receives data. Except when receiving data via a serial port.
      • The device receives data.
      • The USB cable is disconnected and then reconnected.
  • Auto power off

    Specifies the period of time that passes before the device turns off automatically when connected to an AC power outlet.

    

    • The device will automatically enter power off mode when the specified time elapses under the following conditions:

      • The device does not receive data.
      • A LAN cable is not connected. (For wired networks)
      • In idle mode or template selection mode.
      • When no device is connected to the USB port.
      • When not communicating using the serial port.
    • Power off mode is cancelled when the following operations are performed:

      • Any of the device buttons are pressed.
      • The Roll Compartment Cover is opened or closed.
      • The device receives data. Except when receiving data via a serial port.
      • The device receives data.
      • The USB cable is disconnected and then reconnected.
  • Battery charge level

    Specifies the maximum charge level.

    

    To get the longest life from the rechargeable Li-ion battery, select 80 %. Although the number of print jobs that can be printed on a single charge will be less when you select 80 %, you can get a longer overall rechargeable Li-ion battery life.
• Print settings

  • Command mode

    Selects the command mode type.

  • Text direction

    Selects the printing orientation.

  • Print speed

    Selects the device’s printing speed.

    

    • If you increase the print speed, the print result may become lighter.
    • If the barcode on the printed label is difficult to read, select a slower printing speed.
  • Print density

    Adjusts the device’s printing density.

    Changing the Energy rank setting in the Paper size setup can further increase the print density. For more information, see Related Topics: Paper Size Setup.

  • Align paper leading edge when the cover is closed

    Selects whether the paper is automatically fed when the cover is closed.

  • Auto cut

    Sets the cutting method when printing multiple labels.

  • Cut per sheet

    Specifies how many labels to print before cutting when "Auto cut" is set to "Auto cut" or "Auto cut and cut at end" (maximum of 99 labels).

  • Exit position

    Selects the media output location.

  • Auto speed configuration

    Automatically adjusts the printing speed and prints at the optimal print density.

• Key functions

  • Feed Key function

    Selects the operation performed when is pressed. If Program settings is selected, click Browse and select the command file.

  • Function key function

    Selects the operation performed when is pressed. If Program settings is selected, click Browse and select the command file.

    If the Cutter is attached, manual cutting can be set using the Function Key.

  • Menu Key Function

    Selects the operation performed when Menu / (Select) button is pressed. If Program settings is selected, click Browse and select the command file.

• Beeper

  • Volume

    Selects the beeper volume.

• Print log

  • Save printer print log

    Selects whether to save the device’s print log.

• Print information report

  • Contents

    Selects the information you want to include in the information report.

• Other

  • JPEG printing settings

    Selects the method of image processing when printing JPEG images.

  • Print data after printing

    Specifies whether print data is erased after printing.

  • Linerless

    Selects to enable support for Linerless rolls.

When you use standard media, it is unnecessary to adjust the sensors.

• Print position / sensor

  • Printing reference point adjustment

    Adjusts the position of the reference point (point of origin for printing). This corrects printing misalignments resulting from differences in device models or from the fixed margins of some software.

    The reference point cannot be adjusted for raster printing.

  • Tear adjust

    • Adjusts the Tear Bar tear-off position for paper media.

      NOTE

      Depending on the media type, the cut position and margins may not match your settings. If this occurs, adjust the Tear Adjust setting, and then try to print again.

    • When the Use Peeler Function or Auto Cutter Function in the device driver is enabled and the peeled labels are jammed or are not ejected correctly after printing, adjust the Tear Adjust setting, and then try to print again.

• Media sensor(Transmissive/Gap)

  • Detection sensitivity

    Adjusts the sensitivity of gap (spacing) detection for die-cut labels.

  • Luminescence adjustment

    Adjusts the amount of light emitted by the transmissive/gap sensor.

• Media sensor(Reflective/Bar)

  • Mark detection sensitivity

    Adjusts the sensitivity of black mark detection.

  • Luminescence adjustment

    Adjusts the amount of light emitted by the reflective/black mark sensor.

• Media sensor (Peeler)

  Specifies the settings when the Label Peeler (optional) is used.

  • Detection sensitivity

    Adjusts the precision of the sensor that detects whether the label has been peeled.

• Media calib

  • Media calib liner width

    Sets the calibration value for the liner width (maximum of 255).

• Basic

  • Language

    Specifies the language displayed on the LCD.

  • Backlight

    Sets the backlight on or off.

  • Backlight timeout

    Sets the period of time before the backlight turns off if the device is not used.

  • Unit

    Specifies the default unit.

  • Display brightness

    Sets the display brightness.

  • LCD contrast

    Sets the contrast of the LCD.

• Template settings

  • Home screen settings

    Specifies whether the device operates in P-touch Template Mode.

    P-touch Template Mode allows you to enter only text and print labels using a previously configured template.

  • Template touchscreen settings

    Sets the display format for the template touch mode screen.

  • Search type

    Sets the search method when searching for a specific template from the template list.

  • Show preset templates

    Sets whether or not to display the preset templates on the device.

  • Confirm print

    Specifies whether a message appears before printing so that the number of copies can be confirmed.

• Date&Time

  • Date format

    Selects the date format for the clock.

  • Time format

    Selects the time format for the clock.

  • Clock

    Sets the clock function.

  • Set clock

    Sets the date and time.

  • Synchronize with SNTP server

    Synchronizes time with the SNTP server.

  • Time zone

    Sets the time zone.

• Custom QR code

  • QR code data

    Creates custom QR code data based on the required text or web page and displays it on the device's LCD. The displayed QR code can be read using a mobile device to retrieve information.