Search

Site Map

Home > Routine Maintenance > Clean the Machine > Clean the Drum Unit Using Drum Dot Print

Clean the Drum Unit Using Drum Dot Print

If your printout has dots or other repeating marks at 94 mm intervals, the drum may have foreign material, such as glue from a label, stuck on the drum surface.

DCP-L2531DW/DCP-L2535DW/DCP-L2550DW/MFC-L2710DW/MFC-L2713DW/MFC-L2715DW/MFC-L2716DW

  1. Make sure the machine is in Ready mode.
  2. Press image or image to display the [Print Reports] option, and then press OK.
  3. Press image or image to select the [Drum Dot Print] option.
  4. Press Start.
    The machine prints the Drum Dot Check Sheet.
  5. Press and hold image to turn the machine off.
  6. Open the front cover.
    image
  7. Remove the toner cartridge and drum unit assembly from the machine.
    image
  8. Push down the green lock lever and take the toner cartridge out of the drum unit.
    image
  9. Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side.
    image
  10. Use the numbered markers next to the drum roller to find the mark on the drum. For example, a dot in column 2 on the check sheet means that there is a mark in drum region “2”.
    image
  11. Turn the edge of the drum unit towards you while looking at the drum surface to find the mark.
    image
    IMPORTANT
    • To avoid print quality problems, DO NOT touch the surface of the drum unit, only the wheel on the end.
  12. Wipe the surface of the drum gently with a dry cotton swab until the mark or foreign material on the surface comes off.
    image
    NOTE
    DO NOT clean the surface of the photosensitive drum with a sharp object or any liquids.
  13. Push the toner cartridge firmly into the drum unit until you hear it lock into place.
    image
    image
    Make sure you put the toner cartridge in correctly or it may separate from the drum unit.
  14. Install the toner cartridge and drum unit assembly back into the machine.
    image
  15. Close the front cover of the machine.
  16. Press image to turn the machine on.

HL-L2395DW/MFC-L2730DW/MFC-L2750DW/MFC-L2751DW/MFC-L2770DW/MFC-L2771DW

  1. Make sure the machine is in Ready mode.
  2. Press image[Settings]>[All Settings]>[Print Reports]>[Drum Dot Print].
  3. Press [Yes].
    The machine prints the Drum Dot Check Sheet.
  4. Press image.
  5. Press and hold image to turn the machine off.
  6. Open the front cover.
    image
  7. Remove the toner cartridge and drum unit assembly from the machine.
    image
  8. Push down the green lock lever and take the toner cartridge out of the drum unit.
    image
  9. Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side.
    image
  10. Use the numbered markers next to the drum roller to find the mark on the drum. For example, a dot in column 2 on the check sheet means that there is a mark in drum region “2”.
    image
  11. Turn the edge of the drum unit towards you while looking at the drum surface to find the mark.
    image
    IMPORTANT
    • To avoid print quality problems, DO NOT touch the surface of the drum unit, only the wheel on the end.
  12. Wipe the surface of the drum gently with a dry cotton swab until the mark or foreign material on the surface comes off.
    image
    NOTE
    DO NOT clean the surface of the photosensitive drum with a sharp object or any liquids.
  13. Push the toner cartridge firmly into the drum unit until you hear it lock into place.
    image
    image
    Make sure you put the toner cartridge in correctly or it may separate from the drum unit.
  14. Install the toner cartridge and drum unit assembly back into the machine.
    image
  15. Close the front cover of the machine.
  16. Press image to turn the machine on.
Related Information
Was this page helpful?

Yes

No

find moreaccept