Toner

Toner Life

View the approximate remaining toner life.

Test Print

Print a test page.

Network

Wired LAN

Access the Wired LAN setting menus.

WLAN

Access the WLAN setting menus.

Tray Setting

Paper Type

Set the type of paper in the paper tray.

Paper Size

Set the size of paper in the paper tray.

Check Size

Select whether to display a message telling you to check that the size and type of the paper in the machine and the machine's Paper Size and Paper Type settings match.

Tray Use: Copy

(Available only for certain models)

Select the tray to be used for Copy.

Tray Use: Print

(Available only for certain models)

Select the tray to be used for Print.

Wi-Fi Direct

-

Access the Wi-Fi Direct setting menus.

Eco Mode

-

Turn the following machine settings on at the same time.

• 2-sided Print:Long Edge(Available only for certain models)
• Sleep Time:0Min
• Dim Timer:10Secs

All Settings

-

Configure the detailed settings.

Tray Setting

Paper Type

Set the type of paper in the paper tray.

Paper Size

Set the size of paper in the paper tray.

Check Size

Select whether to display a message telling you to check that the size and type of the paper in the machine and the machine's Paper Size and Paper Type settings match.

Tray Use: Copy

(Available only for certain models)

Select the tray to be used for Copy.

Tray Use: Print

(Available only for certain models)

Select the tray to be used for Print.

Beep

-

Adjust the beeper volume.

LCD Settings

Backlight

Adjust the brightness of the LCD backlight.

Dim Timer

Set how long the LCD backlight stays on after you go back to your Home screen.

Screen Settings

Scan Screen

Set the default Scan screen settings.

Ecology

Eco Mode

Turn the following machine settings on at the same time.

• 2-sided Print:Long Edge((Available only for certain models))
• Sleep Time:0Min
• Dim Timer:10Secs

Toner Save

Increase the page yield of the toner cartridge.

Sleep Time

Set the number of minutes before the machine enters Sleep mode.

Quiet Mode

Decrease printing noise.

Auto Power Off

Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode. Choose Off if you do not want the machine to go into Power Off mode.

Replace Toner

-

Set the machine to continue printing after the LCD displays Replace Toner.

(Select shortcut button.)

Rename

Change the shortcut name.

Edit

Change the shortcut settings.

Delete

Delete the shortcut.

Emulation

-

-

Select the emulation mode.

Print Options

Font List

HP LaserJet

Print a list of the machine’s internal fonts.

BR-Script 3

Test Print

-

Print a test page.

2-sided

2-sided Print

-

Enable or disable 2-sided printing and choose long edge or short edge.

Single Image

-

For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time.

Auto Continue

-

-

Select this setting if you want the machine to clear paper size errors, and to use the paper in the tray.

HP Tray Command

-

-

Select the correct version of HP LaserJet tray emulation.

Reset Printer

-

-

Restore the printer settings to the factory settings.

Wired LAN

TCP/IP

BOOT Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(up to 32 characters)

WINS Configuration

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Ethernet

-

-

Select the Ethernet link mode.

Wired Status

-

-

View the current wired status.

MAC Address

-

-

View the machine's MAC address.

Set to Default

-

-

Restore the wired network settings to the factory settings.

Wired Enable

-

-

Turn the Wired LAN interface on or off manually.

WLAN

TCP/IP

BOOT Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(up to 32 characters)

WINS Configuration

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Setup Wizard

-

-

Configure your wireless network settings manually.

WLAN Assistant

-

-

Configure your wireless network settings using the Brother installation disc.

WPS

-

-

Configure your wireless network settings using the one-button push method.

WPS w/ PIN Code

-

-

Configure your wireless network settings using WPS with a PIN.

WLAN Status

Status

-

View the current wireless network status.

Signal

-

View the current wireless network signal strength.

SSID

-

View the current SSID.

Comm. Mode

-

View the current Communication mode.

MAC Address

-

-

View the machine's MAC address.

Set to Default

-

-

Restore the wireless network settings to the factory settings.

WLAN Enable

-

-

Turn the WLAN on or off manually.

Wi-Fi Direct

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code.

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Device Information

Device Name

-

View your machine's device name.

SSID

-

View the Group Owner's SSID.

When the machine is not connected, the LCD displays Not Connected.

IP Address

-

View your machine's current IP Address.

Status Information

Status

-

View the current Wi-Fi Direct network status.

Signal

-

View the current Wi-Fi Direct network signal strength.

When your machine acts as Group Owner, the LCD always indicates a strong signal.

I/F Enable

-

-

Turn the Wi-Fi Direct connection on or off.

NFC

(Available only for certain models)

-

-

-

Turn the NFC function on or off.

Web Connect Settings

Proxy Settings

Proxy Connection

-

Change the Web connection settings.

Address

-

Port

-

User Name

-

Password

-

Network Reset

-

-

-

Restore all network settings back to the factory settings.

User Settings

Print a list of your settings.

Printer Settings

Print a list of your Printer settings.

Network Configuration

Print a list of your Network settings.

Print File List

Print a list of data saved in the machine's memory.

Drum Dot Print

Print the Drum Dot Check Sheet.

WLAN Report

Print the wireless LAN connection results.

Serial No.

-

Check your machine's serial number.

Firmware Version

Main Version

Check your machine's firmware version.

Sub1 Version

Firmware Update

-

Update your machine to the latest firmware.

Firmware Auto Check

-

View firmware information on the Home screen.

Page Counter

Total

Check the total number of pages the machine has printed.

Copy

Print

Other

Parts Life

Drum

Check the percentage of the supplies' life that remains available.

Reset

Machine Reset

Restore all the machine settings that you have changed.

Network Reset

Restore all network settings back to the factory settings.

All Settings

Restore all the machine's settings back to the factory settings.

Factory Reset

Restore all settings back to the factory settings.

Local Language

(Available only for some countries.)

-

Change your LCD language.