Tray Setting

Paper Type

-

Set the type of paper in the paper tray.

Paper Size

-

Set the size of paper in the paper tray.

Check Size

-

Select whether to display a message telling you to check that the size and type of the paper in the machine and the machine's Paper Size and Paper Type settings match.

Ecology

Eco Mode

-

Turn the following machine settings on at the same time.

• 2-sided Print:Long Edge(Available only for certain models)
• Sleep Time:0Min

Toner Save

-

Increase the page yield of the toner cartridge.

Sleep Time

-

Set the number of minutes before the machine enters Sleep mode.

Quiet Mode

-

Decrease printing noise.

Auto Power Off

-

Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode.

LCD Contrast

-

-

Adjust the LCD contrast.

Replace Toner

-

-

Set the machine to continue printing after the LCD displays Replace Toner.

Density

-

Adjust the density.

Quality

-

Choose the Copy resolution for your type of document.

Contrast

-

Adjust the contrast for copies.

ID Copy

Density

Adjust the density.

Quality

Choose the Copy resolution for your type of document.

Contrast

Adjust the contrast for copies.

2in1/1in1

Make 2 in 1 ID copies.

Emulation

-

-

Set the printer emulation mode.

Print Options

Font List

HP LaserJet

Print a list of the machine’s internal fonts.

BR-Script 3

Test Print

-

Print a test page.

2-sided

2-sided Print

-

Turn 2-sided printing off or on and select flip on long edge or short edge.

Single Image

For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time.

Auto Continue

-

-

Select this setting if you want the machine to clear paper size errors, and to use the paper in the tray.

Tray Command

-

-

Select this setting if a tray mismatch appears when you use the HP drivers.

Reset Printer

-

-

Restore the printer settings to the factory settings.

Test Print

Print a test page.

2-sided

Turn 2-sided printing off or on and select flip on long edge or short edge.

Auto Continue

Select this setting if you want the machine to clear paper size errors, and to use the paper in the tray.

Reset Printer

Restore the printer settings to the factory settings.

Wired LAN

TCP/IP

Boot Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(Up to 32 characters)

WINS Config

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Ethernet

-

-

Select the Ethernet link mode.

Wired Status

-

-

View the current wired status.

MAC Address

-

-

View the machine's MAC address.

Set to Default

-

-

Restore the wired network settings to the factory settings.

Wired Enable

-

-

Turn the Wired LAN interface on or off manually.

WLAN

TCP/IP

Boot Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(Up to 32 characters)

WINS Config

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Setup Wizard

-

-

Configure your wireless network settings manually.

WLAN Assistant

-

-

Configure your wireless network settings using the Brother installation disc.

WPS

-

-

Configure your wireless network settings using the one-button push method.

WPS w/PIN Code

-

-

Configure your wireless network settings using WPS with a PIN.

WLAN Status

Status

-

View the current wireless network status.

Signal

-

View the current wireless network signal strength.

Channel

-

View the current wireless network channel.

Speed

-

View the current wireless network speed.

SSID

-

View the current SSID.

Comm. Mode

-

View the current Communication mode.

MAC Address

-

-

View the machine's MAC address.

Set to Default

-

-

Restore the wireless network settings to the factory settings.

WLAN Enable

-

-

Turn the WLAN on or off manually.

Wi-Fi Direct

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code.

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Device Info.

Device Name

-

View your machine's device name.

SSID

-

View the Group Owner's SSID.

When the machine is not connected, the LCD displays Not Connected.

IP Address

-

View your machine's current IP Address.

Status Info.

Status

-

View the current Wi-Fi Direct network status.

Signal

-

View the current Wi-Fi Direct network signal strength.

When your machine acts as Group Owner, the LCD always indicates a strong signal.

Channel

-

View the current Wi-Fi Direct network channel.

Speed

-

View the current Wi-Fi Direct network speed.

I/F Enable

-

-

Turn the Wi-Fi Direct connection on or off.

Network Reset

-

-

-

Restore all network settings back to the factory settings.

WLAN

TCP/IP

Boot Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(Up to 32 characters)

WINS Config

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Setup Wizard

-

-

Configure your wireless network settings manually.

WLAN Assistant

-

-

Configure your wireless network settings using the Brother installation disc.

WPS

-

-

Configure your wireless network settings using the one-button push method.

WPS w/PIN Code

-

-

Configure your wireless network settings using WPS with a PIN.

WLAN Status

Status

-

View the current wireless network status.

Signal

-

View the current wireless network signal strength.

Channel

-

View the current wireless network channel.

Speed

-

View the current wireless network speed.

SSID

-

View the current SSID.

Comm. Mode

-

View the current Communication mode.

MAC Address

-

-

View the machine's MAC address.

WLAN Enable

-

-

Turn the WLAN on or off manually.

Wi-Fi Direct

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code.

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Device Info.

Device Name

-

View your machine's device name.

SSID

-

View the Group Owner's SSID.

When the machine is not connected, the LCD displays Not Connected.

IP Address

-

View your machine's current IP Address.

Status Info.

Status

-

View the current Wi-Fi Direct network status.

Signal

-

View the current Wi-Fi Direct network signal strength.

When your machine acts as Group Owner, the LCD always indicates a strong signal.

Channel

-

View the current Wi-Fi Direct network channel.

Speed

-

View the current Wi-Fi Direct network speed.

I/F Enable

-

-

Turn the Wi-Fi Direct connection on or off.

Network Reset

-

-

-

Restore all network settings back to the factory settings.

User Settings

-

Print a list of your settings.

Print Settings

-

Print a list of your Printer settings.

Network Config

(For models with network function)

-

Print a list of your Network settings.

PrintFileList

(Available only for certain models)

-

Print a list of data saved in the machine's memory.

Drum Dot Print

-

Print the Drum Dot Check Sheet.

WLAN Report

(For models with wireless network function)

-

Print the wireless LAN connection results.

Serial No.

-

Check your machine's serial number.

Version

-

Check your machine's firmware version.

Page Counter

Total

Check the total number of pages the machine has printed during its life.

Copy

Print

Other

Parts Life

Toner

View the approximate remaining toner life.

Drum

You can check the percentage of Drum life that remains available.

Reset

Machine Reset

Restore all the machine settings that you have changed.

Network Reset

(For models with network functionality)

Restore all network settings back to the factory settings.

All Settings

Restore all the machine's settings back to the factory settings.

Factory Reset

Restores all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine.

Local Language

(Available only for certain models)

-

Change your LCD language.